How to Take Off Refrigerator Doors to Fit Through a Doorway: Steps

To take off refrigerator doors, unplug, remove the top hinge and lift each door off. Covers measuring, water lines, drawers and reinstalling.

Convenience store with a variety of drinks and products under warm evening light.
Photo: Аlex Ugolkov / Pexels

To take off refrigerator doors so the fridge fits through a doorway, unplug the fridge, empty the door bins, remove the top hinge cover and the bolts that hold the top hinge, then lift each door straight up off its bottom hinge pin. Most fridges need only a socket or nut driver, a Phillips or Torx screwdriver and a helper to hold the door. Plan on 20 to 45 minutes for a standard two-door model, longer for a French door fridge with a water dispenser.

Do you actually need to remove the doors?

You only need to remove the doors if the fridge’s depth with the doors on is wider than the doorway’s clear opening. Measure the narrowest point of the doorway, which is usually between the door stop strips or the edge of the open house door, not the frame. Then check the fridge’s depth in the owner’s manual or spec sheet. Many manuals list two depths: with doors and without doors, and sometimes a third without handles.

Try the easier fixes first:

  • Take off the handles. On many models they add 2 to 3 inches (5 to 8 cm) of depth and come off with a hex key or a set screw underneath.
  • Take the house door off its hinges. Tapping out the hinge pins gives back roughly the door’s thickness, often about 1 3/8 inches (3.5 cm) on interior doors.
  • Pry off the door stop molding, which can add another 1/2 inch (1.3 cm) or so.

Leave at least 1/2 to 1 inch (1.3 to 2.5 cm) of spare room on each side so you can move the fridge without gouging the frame. If you are still choosing a model, our guide to counter-depth and standard-depth fridge sizes explains how depth affects fit.

What tools and prep do you need?

Gather these before you start:

  • A socket set or nut driver (5/16 inch and 3/8 inch are the most common hinge bolt sizes)
  • Phillips and Torx screwdrivers, plus a hex key for handles
  • A putty knife or flat plastic tool to pop off hinge covers
  • Masking or painter’s tape and small bags to label screws, washers and shims
  • A towel to catch drips from the water line
  • A second person

Unplug the refrigerator first. Hinge covers often hide wiring for door switches, lights or the dispenser, and you should never work on those connections with power on. If the fridge has a water dispenser or ice maker, also shut off the water supply valve. Remove food, shelves and bins from the doors so each door is lighter and nothing falls out when it tips. Tape the doors shut while you work on the hinges so they cannot swing open.

Download the owner’s manual before you begin. Brands such as Whirlpool and GE Appliances post manuals on their support sites, and the door removal section shows the exact screw locations for your model.

How do you remove a top-freezer or bottom-freezer door?

  1. Pry off the top hinge cover with the putty knife. If a wire harness runs through it, unplug the connector and tape it to the cabinet so it does not slip inside.
  2. Have your helper hold the upper door. Remove the bolts or screws on the top hinge and lift the hinge away. Keep any shims together with their screws.
  3. Lift the upper door straight up off the center hinge pin and set it on a padded surface, handle side up.
  4. Remove the center hinge bolts, then lift the lower door off the bottom hinge pin.
  5. Note any washers sitting on the hinge pins. They set the door height, and the door will sag or rub if they go missing.

On bottom-freezer models with a pull-out drawer, open the drawer fully, remove the basket, then either lift the drawer front off its rails or remove the screws that hold it to the slides. The manual shows which design you have.

How do you remove French door and side-by-side doors with a water line?

The door with the dispenser carries a water tube and a wire harness, usually through the bottom hinge on side-by-side models and through the top or bottom hinge on French door models. Disconnect both before you lift that door.

  1. Remove the toe grille at the bottom front of the fridge to reach the water tube connection, if your manual places it there.
  2. Press in the collar of the quick-connect fitting and pull the tube out. A small amount of water will drain, so keep the towel ready.
  3. Unplug the wire harness connector at the hinge.
  4. Remove the top hinge screws while your helper holds the door, then lift the door off the bottom hinge and feed the tube and wires out carefully.
  5. Repeat for the other door, which usually has no water line.

Do not cut the water tube to save time. A cut tube needs a repair kit and is a common source of leaks later. Our comparison of French door and side-by-side refrigerators covers how the two door layouts differ.

How do you move the fridge once the doors are off?

Keep the fridge upright if you can, and use an appliance dolly strapped to the side of the cabinet, not the front. Protect the door openings and hinge pins from bumps, since a bent pin will keep the door from closing straight. If the fridge must go on its side for a short trip or a tight turn, read our guide on how to transport a refrigerator and when to plug it in before you restart it.

How do you put the doors back on?

Reinstall the doors in reverse order: lower door first on the bottom pin, then the center hinge, then the upper door and top hinge. Put each washer and shim back where it came from. Reconnect the wire harness and push the water tube fully into its fitting until it stops; a tube that is only partly seated will leak.

Then check the following:

  • Level the fridge with the front leveling legs, slightly higher in front so the doors swing closed on their own.
  • Close a dollar bill in the door gasket at several points. If it slides out with no resistance, adjust the hinge or the leveling legs.
  • On French door models, use the adjustment screw or nut on the hinge to line up the door tops.
  • Turn the water back on, look for drips at the fitting, and run the dispenser for a few minutes to clear air from the line.

Quick answers

Can one person remove refrigerator doors?

One person can remove the screws, but a full-size fridge door is heavy and awkward once it is free of the hinge. Have a helper hold the door while the top hinge comes off.

Will removing the doors void the warranty?

Removing and reinstalling doors is a normal installation step described in most owner’s manuals. Damage from dropped doors or a cut water line is a different matter, so follow the manual’s steps.

Why does the fridge make new noises after I moved it?

A fridge that is out of level or touching a wall can buzz or rattle after a move. See our guide to normal refrigerator clicking versus a bad start relay if the sound continues.

What if the doors still do not fit?

Measure again with the handles off and the house door removed. If the cabinet alone is wider than the opening, you need a different route into the room or a smaller fridge.

Prepared by Shiny Modern with AI-assisted drafting and automated fact checks — see our editorial policy. Spotted an error? Tell us.