Remove a Garbage Disposal and Install a Sink Drain Kit

To remove a garbage disposal, switch off its power at the breaker, unlock the mounting ring and fit a drain kit. Includes the dishwasher hose.

Overhead view of a child straining pasta in a kitchen sink.
Photo: Vikki / Pexels

You can replace a garbage disposal with a regular sink drain in an afternoon with basic hand tools. Turn off the power at the breaker, disconnect the electrical supply, unlock the disposal from its mounting ring, then install a sink drain kit (a strainer basket, a tailpiece and a trap). If a dishwasher drains into the disposal, its hose needs a new connection point on the drain.

What do you need before you start?

Gather everything first so the sink is not out of use for long. A typical job needs:

  • A kitchen sink drain kit with a basket strainer, a tailpiece, and a trap or trap arm that fits your plumbing
  • A dishwasher branch tailpiece (a tailpiece with a side inlet), if you have a dishwasher
  • A screwdriver, adjustable pliers or a wrench, and a disposal wrench or a screwdriver for the mounting ring
  • Plumber’s putty or the sealing gasket that comes with the strainer
  • A bucket, old towels and a flashlight
  • A voltage tester

Most kitchen sinks have a 3-1/2 to 4 inch drain opening, and drain kits are made for that size. Check the package before buying.

How do you safely turn off a garbage disposal?

Switch off the circuit breaker that powers the disposal, then confirm the power is off. Flipping the wall switch alone is not enough, because the wires under the sink can stay live. Use a voltage tester at the wires or the outlet before you touch anything. If the disposal is hardwired and you are not comfortable working with household wiring, hire a licensed electrician for that step.

A disposal plugged into an outlet under the sink is simpler: unplug it after the breaker is off.

How do you disconnect and remove the disposal?

Start by emptying the cabinet under the sink and putting a bucket under the trap. Then work from the bottom up.

  1. Loosen the slip nuts on the trap and the discharge pipe and let any water drain into the bucket.
  2. If the disposal is hardwired, open the cover plate on the bottom, undo the wire connectors and the cable clamp, and pull the cable out. Cap each bare wire end with a wire nut if the circuit will stay in the box.
  3. Pull the dishwasher hose off the disposal’s inlet by loosening its clamp.
  4. Hold the disposal with one hand. Disposals are heavy, so get help if you can. With the other hand, turn the lower mounting ring so its tabs release, which is usually done by inserting a screwdriver into a lug and turning.
  5. Lower the unit and carry it out. The upper mounting parts come off by loosening the screws and removing the snap ring, which frees the sink flange from above.

Brands differ in how the mounting assembly comes apart. Look at the bolts and ring under your sink before you force anything.

How do you install a sink drain kit?

Clean the sink opening of old putty. Press a thin rope of plumber’s putty under the lip of the new basket strainer, or use the gasket supplied, and set it into the opening. From below, slide on the rubber gasket, the cardboard or fiber washer and the locknut, then tighten until the strainer is snug. Wipe off the putty that squeezes out.

Next, attach the tailpiece to the strainer with its slip nut. If you have a dishwasher, use the branch tailpiece so the side inlet faces the dishwasher. Connect the trap to the tailpiece and to the wall drain, adjusting the lengths so the pieces line up without strain. The trap holds a small amount of water that blocks sewer gas, so keep its bend in place.

Where does the dishwasher hose go?

The dishwasher drain hose attaches to the side inlet of the branch tailpiece. Many dishwasher hoses should loop up high under the counter before reaching the drain, which helps keep sink water from running back toward the dishwasher. Check the dishwasher’s installation manual for the exact requirement.

If your disposal had a knockout plug that was never removed, it does not matter once the disposal is gone. For the reverse job, see how to connect a dishwasher drain hose to a garbage disposal. The steps for an inlet plug are in a separate guide on removing the knockout plug.

How do you test for leaks?

Put a dry paper towel under each joint. Fill the sink about halfway, pull the stopper, and watch every connection as the water drains. Then run the dishwasher through a short cycle if you have one, again watching the branch tailpiece and hose clamp. Tighten any wet slip nut a quarter turn at a time, because overtightening plastic nuts can crack them.

Check again after a day. If a joint keeps weeping, take it apart, check the washer is seated flat and rebuild it.

Quick answers

Do you need a plumber to remove a garbage disposal?

Not for most homes, since the work is unbolting parts and installing a drain kit. Call an electrician for hardwired connections you are unsure about and a plumber if the trap or wall drain is corroded or damaged.

What should you do with the electrical wires afterward?

If the circuit was dedicated to the disposal, cap the wires safely inside the box and leave the breaker off, or have an electrician remove the circuit. Never leave bare wires exposed.

Can you install a disposal again later?

Yes. The old mounting assembly is the same style of parts, so a later install is easier when you keep the flange assembly. See the guide on installing a garbage disposal when you have a dishwasher.