Do Power Saver Boxes Cut Your Electric Bill? What NIST Found
No. NIST physicists explain why plug-in power factor devices leave a home bill unchanged, and why residential billing follows real power, not amps.

Plug-in power saver boxes do not lower a home electric bill. A team that included physicists at the National Institute of Standards and Technology (NIST) published a primer on the physics, and its conclusion is that a residential bill stays the same with or without one of these devices. Ads for them often call them Amp Reduction Units or KVARs, short for kilovolt ampere reactive.
The devices do what the ads say in one narrow sense: they reduce the current drawn from the power line. The bill, however, does not follow current alone.
What do these devices claim?
Capacitor-type power factor correction devices are sold as investments that cut the current a house pulls from the grid while still feeding appliances the current they need. A product quoted in a guest post on the Energy Vanguard blog claimed typical savings of 8% to 10% on residential usage and as much as 25%.
Why does less current not mean a smaller bill?
According to a NIST release on EurekAlert, a residential bill is proportional to the product of the power factor and the current. With a correction device the current falls and the power factor rises by a matching amount, so the product is unchanged. The NIST physicist Martin Misakian and two colleagues wrote the nine-page NIST Technical Note 1654 for readers who are not power engineers but have some technical background.
Power factor is the ratio of real power to apparent power, as the Wikipedia article on power factor defines it. Real power is what does work and is measured in watts. Apparent power is the product of current and voltage, and it can be higher than real power because some energy is stored in the load and returned to the source on every cycle. Motors, transformers and fluorescent lamp ballasts can have a power factor well below 1. Heating elements and incandescent lamps sit close to 1.
The Energy Vanguard guest post by Chris Kaiser of Mapawatt makes the same point: a utility charges a home for real power in watts, not apparent power. A home pays for electric power multiplied by the time it is delivered. For how the rest of a bill is split up, see this explainer on electric bill line items.
What does a worked example show?
Kaiser compares two identical 1.2 kW motors on a 120 V circuit. The first has a power factor of .7 and draws 14.29 amps. The second has a correction device and a power factor of .999, and it draws 10.01 amps. The current is lower, but both motors take the same real power from the line, so the utility records the same use.
How little can correction save in a house?
An Electronic Design analysis put numbers on the wiring inside a home. For a 1-hp motor on a 50 ft run of #12 copper cable, it calculated a cable loss of 4.24 W at unity power factor and 7.55 W at a lagging power factor of 0.75. The top three entries in its table added up to $0.09. Against a monthly bill the article estimated at $60 to $80, that is about 0.1%.
The same article looked at prices. Devices advertised on eBay ranged from $5.99 to $2000, and a Square D capacitor in a mounting box was listed at $49.99. The author concluded that the savings would not justify buying the equipment. It also noted that one correction device cannot suit every appliance, because a motor’s power factor depends on its design, rating and load.
Do the devices have any use?
The NIST authors say they may help the environment, though not your bill. Power is lost to resistance on the way from a local transformer to a house. A home with a correction device draws less current, so those losses shrink, which could reduce greenhouse gas emissions at a utility that burns fossil fuels. Misakian added that a buyer would also have to count the emissions from making the device. He said readers must look into the details of these options themselves.
Utilities usually bill industrial and commercial customers more when their power factor is low, according to Wikipedia. Mapawatt makes a similar point about industrial users billed for peak demand. Homes are not billed that way.
To see what an appliance actually costs to run, the appliance electricity cost calculator estimates running cost from its draw and your rate.
Quick answers
Will a power saver box lower my kWh use?
The NIST primer and the other sources say no for a typical home. The box changes the current from the line and the power factor, and the energy the meter counts stays the same.
Why do ads show lower amps after installing one?
The current drawn from the line does drop. Kaiser’s motor example shows 14.29 amps falling to 10.01 amps with the same real power delivered.
Who might be billed for power factor?
Industrial and commercial customers with a low power factor, according to Wikipedia, and some industrial users billed for peak demand, according to Mapawatt.
Checked against official sources in November 2026. Hours, prices and rules change: confirm on the official page before you go or apply.


